What does trim do? And why should you stay out of the red?
18 Nov 2026
At the very top of the mixer, at the head of every channel, there is a small knob: TRIM (GAIN on some mixers). It's one of the knobs beginner DJs touch least, and one that makes the biggest difference when they do. In this article we go through the lesson note video narrated by Gwen de Lien, what trim does and why you shouldn't go into the red, together with booth practice.
What is trim?
Trim is the input level that comes before the fader. The moment the track's audio enters the mixer channel it passes through the trim first, then the EQ, then the fader and finally the master output. So trim decides how much "signal" enters the channel. The fader sets how much of that signal is heard in the mix.
The distinction matters: level with the trim, mix with the fader.
Why does every track need a different trim?
Every track is mastered at a different loudness. A house track released in the early 2000s can be clearly quieter than a tech house track released in 2025. Even two tracks from the same period can differ by a few decibels because they were mastered in different studios with different approaches. One shouts, the other whispers.
Without trim you would have to bring the fader to a different place in every transition, and the sound would jump up or drop when the incoming track opened. With trim you bring every track to the same level, so both tracks sound equal with the faders in the same position.
Reading the channel meter
Next to every channel there's a level meter: green at the bottom, yellow/orange in the middle, red at the very top. While you cue the incoming track in your headphones, watch the meter:
- If the meter moves around 0 on the loudest parts of the track, you're in the right place.
- If it regularly goes above the orange, turn the trim down a little.
- If it stays in the middle of the green, turn the trim up a little.
A practical method: wherever the playing track's meter is dancing, bring the incoming track to the same place with the trim. Let your eyes and ears work together.
What happens if you go into the red?
The red zone of the meter is where the signal hits the limit of what the mixer can handle. When that limit is exceeded the sound clips: the peaks of the waveform are cut off and a harsh, dirty distortion is added.
- The kick cracks. Instead of round and full, the kick sounds broken and harsh.
- The bass distorts. The bassline loses its definition and turns into a rumble.
- The club system makes it bigger. Distortion that sounds like slight harshness in headphones spreads across the whole room on a big system. On top of that the system's protection may kick in and turn the sound down, the worst possible moment for the floor.
Going into the red doesn't make it more powerful. It makes it worse, not louder.
The rule: level with the trim, mix with the fader, keep the master out of the red
- Level with the trim: bring every new track to around 0 on the channel meter.
- Mix with the fader: manage the level in transitions with the fader.
- Never let the master go into the red: the mixer's master meter should also stay around 0, like the channels. When two tracks play together the master rises easily; swapping the bass with the EQ is the best way to prevent that.
What if the sound isn't loud enough?
Sometimes in the booth it feels like "it's not loud enough". The most common mistake is to push the mixer, driving the trims and master into the red. The right move: don't push the mixer, tell the resident DJ. The venue's resident DJ hears that system every night; they know best where the level is set, what the system's limits are and how the booth monitors work. If needed they can raise the system level from the right place, or adjust the booth monitor so you hear better. In many cases the problem isn't the sound on the floor, it's the monitor in the booth.
Common mistakes
- Never touching the trim: playing every track with the same trim makes transitions jump between tracks of different loudness.
- Using the fader as a trim: trying to compensate for a quiet track by pushing the fader all the way makes transitions harder to control.
- Trusting only your eyes: the meter guides you but your ear has the final say; perceived loudness can differ, especially across genres.
- Forgetting the master: even if the channels are right, the sound distorts if the master is in the red.
At Institute of Sound
You learn trim, gain structure and master level on Pioneer DJ mixers with club-level monitors, hearing with your own ears how the sound breaks when it goes into the red. Learn it with your own ears in the booth.
Contact us for details.
Narration: Gwen de Lien



