Skip to content
Morotune
LIVE
INSTITUTE OF SOUND · Lesson notes

Mixing with EQ: 3 knobs, 3 steps

16 Nov 2026

Moving from one track to the next is the most visible and the least understood part of DJing. Someone watching only sees a fader going up. But the real work of a good transition happens on three small knobs on every mixer channel: the EQ. In this article we unpack the method from the lesson note video narrated by Gwen de Lien, the "3 knobs, 3 steps" rule, in enough detail that you can actually use it in the booth.

What is EQ and where is it on the mixer?

On a club mixer every channel has three (on some models four) rotary knobs: HI, MID and LOW. Each one controls a frequency region:

  • HI (treble): hi-hats, cymbals, shakers, the brightness of the vocal and the "air" of the track. Roughly above 2–3 kHz.
  • MID: vocals, synths, chords, the body of the melody. Roughly 200 Hz to 2–3 kHz.
  • LOW (bass): the body of the kick and the bassline. Roughly below 200 Hz; the region you feel in your chest on the dance floor.

With the knob in the middle (twelve o'clock) the band plays as it is. Turning left cuts it, turning right boosts it. On club mixers turning fully left usually removes the band almost completely; this is called a kill. The real job of EQ is not to make the sound "nicer" but to decide who speaks in which frequency while two tracks play at the same time.

Why do we mix with EQ?

If two tracks play at full level together, every band doubles: two kicks, two basslines, two sets of hi-hats, two vocals. The result is crowded, blurry and loud. In the low end especially, two basslines on top of each other turn the sound into mud, and a club system makes it even bigger. Mixing with EQ is how you leave one single "owner" in each frequency region even while both tracks are playing. The crowd doesn't hear the transition; it just feels the music keep flowing.

Preparation: start the incoming track the right way

Before the transition the incoming track should already be beatmatched in your headphones (same tempo and phase). Then:

  1. Turn the incoming track's LOW fully down.
  2. Start MID and HI slightly cut (ten or eleven o'clock is a good start).
  3. Make sure the trim matches the other track.
  4. At the start of a phrase, on the first beat of a 16 or 32 beat section, open the fader.

At this point the room hears only the highs and mids of the new track, gently. The bass still belongs entirely to the outgoing track. You've opened the fader but not swapped anything yet; you've only invited the new track into the room.

Step one: HI

Slowly bring the incoming track's HI up to the middle. At the same time lower the outgoing track's HI by the same amount. The hi-hats change hands: the "tick" at the very top of the groove now comes from the new track. This is the lowest-risk step, because overlapping highs can blend without hurting the ear. Starting the transition with the highs sounds natural and buys you time.

Step two: MID

Do the same for MID. Open the incoming MID, lower the outgoing one. Vocal and melody change hands. This is where you need to pay attention: two vocals, or two melodies in different keys, left at full level together will sound "wrong". If the tracks are not harmonically compatible (far apart on the Camelot wheel), keep the MID swap short and pull out the outgoing vocal early.

Step three: LOW (the bass swap)

The most important and the most delicate step. At the start of a new phrase swap the basses: the outgoing LOW comes down while the incoming LOW goes up. You can do this two ways:

  • Smooth swap: turn both knobs in opposite directions over a few bars. Common in house, deep house and afro house.
  • Hard swap: on the first beat of the phrase, kill the outgoing LOW in one move while opening the incoming LOW. Preferred in tech house and techno to keep the energy.

The golden rule: two basslines must never play at full level at the same time. Two basses that sound "not bad" in headphones turn into an undefined rumble on a club system.

Final touch: quietly close the outgoing track

Once all three bands have moved to the new track, the floor is on the new track. The outgoing one may still be playing in the background with an open fader and cut EQs. Close it quietly with the fader towards the next phrase and return its EQs to the middle; you'll use that channel again in the next transition.

The most common EQ mistakes in the booth

  • Forgetting to cut the bass: starting the incoming track with LOW open means two kicks colliding in the first second of the transition.
  • Not counting phrases: swapping the bass in the middle of a section gives the floor a "something slipped" feeling.
  • Turning everything at once: turning all three knobs together shortens the transition but costs you control. Order: HI → MID → LOW.
  • Using EQ to make things louder: boosting the EQ fully to the right doesn't give you volume, it distorts. Level is the trim's job.
  • Not knowing the mixer: every mixer's EQ has a different character; a knob that kills on one model only cuts a few decibels on another. Listen to the mixer in the booth before you play.

Practice tip

With two tracks at the same tempo, practise only the LOW swap for ten minutes. Then repeat the same transition adding HI and MID. Very soon your ear will start to feel uncomfortable when two basslines collide; that means you're on the right track.

At Institute of Sound

You learn EQ mixing on Pioneer DJ equipment in one-to-one lessons, with tracks you choose yourself. First in headphones, then on club-level monitors, hearing the difference. Learn it with your own ears in the booth.

Contact us for details.

Narration: Gwen de Lien

More stories

→ See all
ABOUT EVENTS RADIO OMELO PNIGHT SESSION
OMELO P – Omeloncholia Radio #002